"73832" "feet" "inches" "sq inches" "lbs/ft" "feet/min" "lbs/cu ft" "stph" "ltph" "meters" "sq meters" "kg/meter" "kg/cu meter" "meters/sec" "Run Calc" "mtph" "mm" "kW" "sec" "short Tons" "Long Tons" "Metric Tons" "degrees" "Design Load Capacity" "Belt Speed" "Belt Width" "Material Bulk Density" "Trough Idler Angle" "Surcharge Angle" "Width Between Skirt boards" "Using Center Roll of this Length" "Bed Depth" "Feeder Coefficient" "Edge distance" "Load width" "Load cross sectional area" "Full load surcharge" "Full load trapezoid" "Depth at skirtboard at full" "Load on belt at full" "Full load capacity" "Edge dist - standard" "Load width - maximum" "Full load cross sectional area" "Full load surcharge" "Full load trapezoid" "Depth at skirtboard at full" "Load on belt at full" "Full load capacity" "%" "Calculate Feeder" "Item" "Units" "Metric" "Feeder Capacity" "" "Project Name or Number" "Project Phase or Site" "Area or Location" "Machine Name" "Enter conveyor identifying data. All optional." "Save before closing?" "Equal Roll Idlers ratio:" "Open Conveyor Calculations File" "Equal Roll Center Roll Ratio" "Enter a value that is the ratio of center roll width" "divided by belt width - Default = 371/1000" "The current value is " "Equal Roll Idlers using this ratio:" "Save to Conveyor Calculations File" "File not saved" "Worksheet data not found" "One or more of the data entry boxes contains invalid data" "Please correct and try again" "Export Worksheet Data to File" "Select File to Open" "Save" "No record selected" "Double click to delete" "File name is invalid" "File not found" "Not a Dialect file" "Calculate Conveyor before Export" "Save Text File" "No worksheets saved to this file" "Unable to Open File" "Capacity" "Logo Font" "Print Capacity or Power" "Selected Power" "All Power" "Minimize" "Click a tree list item or text box and then the Help button" "Ratio of center roll length to belt width" "Edit all input values" "Clear drag area" "Create spreadsheet importable text file" "Clear drag area" "Reset drag area" "Mark as Obsolete" "" "" "Full length Skirt boards are required" "Click Power to get the length along the belt(c173)" "Enter Skirt board length at (e156)" "Click Power again" "Skirt boards Full Length" "New Dialect" "Conveyor Design" "Capacity Not Calculated" "Capacity Ready" "Select Calculation Record to Open" "Power Not Calculated" "Power Ready" "Loading" "Material delivery" "Dialect not saved" "Translate" "Power and Tension Calculation" "Print Page Setup" "Print Preview" "Material delivery" "Material bulk density" "Material depth at Skirt boards" "Belt width" "Belt speed" "FULL Skirt boards? See 134 and 156" "Value" "Conveyor Data" "Driving: wet 0 dry 1" "Lagging: grooved 0 smooth 1 none 2" "Idler seal friction (set or 0)" "Drive: head 1 mid 2 tail 3" "Preferred counter weight" "Regenerative? No = 0 Yes = 1" "Length (horizontal)" "Lift (vertical)" "Trough idler spacing" "Return idler spacing" "Idler roll diameter" "Unit weight of belt" "Material feeding speed" "Drive pulley wrap" "Sag between trough idlers" "Set conveyor factor or enter 0(Ky)" "Low ambient temperature" "Drive efficiency" "Start-up acceleration factor" "Belt cleaner unit friction" "Drive pulley drag" "High tension pulley drag" "High tension pulley count" "Low tension pulley drag" "Low tension pulley count" "Plow drag" "Trippers or accessories drag" "Belt cleaner count" "Skirt board length" "Take-up at drive = 1 No = 0" "Angle of repose" "Take-up for set counterweight" "Conveyor factor as used, (Ky)" "Conveyor factor as calculated, (Ky)" "Temperature friction factor" "Idler total friction factor" "Wrap factor" "Skirtboard friction factor" "Return belt weight at take-up" "Drive count" "Idler rotation speed" "Idler internal friction" "Weight of material on belt" "Approximate carry idlers" "Approximate return idlers" "Approximate length along belt" "Low-ten non-driving pulley drag" "Hi-ten non-driv pulley drag" "Belt cleaner drag" "Skirtboard drag" "Force to accelerate material" "Carry side idler drag " "Carry side belt flexure drag" "Return side belt and idler drag" "Carry side material flexure drag" "Lift tension for material" "Carry side drag at empty" "Carry side drag at loaded" "Return side drag (low tension)" "Return side drag (high tension)" "Effective tension at empty" "Effective tension at loaded" "Sag limit tension" "Drive high tension" "Drive slack tension" "Tail pulley tension at top" "Discharge pulley tension at top " "Average carry side tension" "Min slack tension for sag" "Min slack tension for driving" "Power required at motor (empty)" "Power at motor (design load)" "Power for total drag" "Power to lift material" "Power to accelerate material" "Power loss of belt cleaners" "Power loss of skirt boards" "Power drive loss at empty" "Power drive loss at loaded" "Pulleys e147 - 152" "Equipment e153 - 158" "Calculated" "Conveyor Factors c159 - 173" "Drag Details c174 - 182" "Drag Summaries c183 - 187" "Belt Tensions c188 - 197" "Power c198 - 199" "Power Loss c200 - 206" "Drag Data" "meters/min" "N" "kN" "kgf" "" "rpm" "HP" "Conveyor Data e128 - 146" "lb-force" "FEEDER DATA" "Capacity Data c120 - 124" "Obsolete" "File" "Edit" "Power Form" "Language" "Options" "Window" "Help" "New Worksheet" "Open" "Save" "Save As" "Close" "Page Setup" "Feeder Data" "Print Preview" "Print" "Exit" "Names" "Open Dialect File" "" "Translate from default" "Translate from current" "Conveyor" "Feeder" "Units" "Idlers" "" "Metric Tons" "Long Tons U S" "Short Tons U S" "Equal Roll" "Wide Center Roll" "Flat" "Change Center Roll Ratio" "" "" "Metric Force Units" "" "Newtons N" "Kilonewtons kN" "Kilograms - force kgf" "Meters per second" "" "Cascade" "Horizontal" "Vertical" "Help Topics" "About" "ALL SKIRTED" "Close" "Input" "Power" "Export" "Reset" "Clear" "OK" "Cancel" "Apply" "Worksheet - Project - Conveyor Identifier" "Change Feeder Parameters" "Delete" "Cancel" "Zoom" "Next" "Copy" "CONVEYOR DATA" "BELT FULLY LOADED" "File Off List" "" "Feeder Unknown Variable" "Select Dialect" "Long and Metric" "Short and Metric" "" "Logo Line 1" "Logo Line 2" "U S English (Default)" "" "" "Design Load Capacity" "Belt Speed" "Belt Width" "Material Bulk Density" "Trough Idler Angle" "Surcharge Angle" "Width Between Skirtboards" "Using Center Roll of this Length" "Bed Depth" "Feeder Coefficient" "Delete Dialect File"